Thursday, July 3, 2008

The American Moederfiets (mother bike)

Resized_DSC7103
Or in this photo, Father bike


We finished building the kid seats complete with sunshades.

We used 12mm marine plywood for its waterproof glue (avoid delamination if an edge gets chipped then wetted. I pre-drilled a ton of holes on each junction so as not to split the wood when screwing. I striped the mating edge with gorilla glue then screwed together. So all said and done the bonds should be quite strong.

The order of assembly was seat back to wedge shaped rear facing support. Then I attached the sides drilling from the backsides of the seats, so that the upper portions of the seats were fully assembled. Then I lined them up on the base, clamped, pre-drilled, glued and screwed the uppers down to the base.

ResizedDSC7134

Some tips on working with marine plywood, its has more plys for a given thickness, and consequently requires some extra care in working with it. We clamped a backer lock for all holes drilled through the wood such as for the tee nuts, otherwise it will blow out the backside and make a mess of splinters. Also you have to be real careful sanding the edges or routing to avoid splintering it. I even had to saw away from the grain line and use very sharp finishing blades to keep from chipping it like mad.

For the straps I had a local shop put metal grommets in webbing so that I count mount tee-nuts from the back sides for a threaded insert then use a fastener to mount the straps via the metal grommets. Its all VERY secure.

The assembly and prep sanding of the seats took the better part of a day with my wife and I working largely together. The puttying, further sanding, staining, varnishing was done in a little bit of free time here and there over the following week. Exactly one week after starting, we were assembling it on the bike and putting the finishing
touches on it.

The pads are a cordura covers that my wife sewed with a combination of a closed cell foam backing and an open cell foam upper for breathability and shock absorbtion.

Resized_DSC7083

10 comments:

derek said...

I want one so bad and I don't even have kids. The nephews would love it though :)

Nickie, Anthony, Samuel, and Anders said...

Yeah, they definitely like this a lot better than riding in the trailer. The extra interaction is a pretty sweet deal besides that fact that its so much lighter and more efficient than a trailer.

Fritz said...

Ah, never mind about the question I posted in Flickr, I think this post answers it.

Anonymous said...

I'm curious how you attached the base to the snapdeck?

The Stouts said...

We used some industrial p-clamps that go around the v-racks, and put tee nuts into to top of the seat base. Then thread a stainless screw through the p-clamp up into the tee-nut from bottom side.

gwadzilla said...

sweet stuff!

I am going to have to throw this information on my page

people have got to see this!

Miriam said...

Interesting to know.

Anastasia said...

How did you make the sunshades? I'm after something like that for ages!

The Stouts said...

Hi Anastasia,

The shades are made by Dueter for kid carrying backpacks. We had one of their packs and realized we could use the shade on the bike. I think they do sell them separately.

Happy Riding!
Nickie

日月神教-向左使 said...

AV,無碼,a片免費看,自拍貼圖,伊莉,微風論壇,成人聊天室,成人電影,成人文學,成人貼圖區,成人網站,一葉情貼圖片區,色情漫畫,言情小說,情色論壇,臺灣情色網,色情影片,色情,成人影城,080視訊聊天室,a片,A漫,h漫,麗的色遊戲,同志色教館,AV女優,SEX,咆哮小老鼠,85cc免費影片,正妹牆,ut聊天室,豆豆聊天室,聊天室,情色小說,aio,成人,微風成人,做愛,成人貼圖,18成人,嘟嘟成人網,aio交友愛情館,情色文學,色情小說,色情網站,情色,A片下載,嘟嘟情人色網,成人影片,成人圖片,成人文章,成人小說,成人漫畫,視訊聊天室,性愛,ut聊天室,情色遊戲,情色a片,情色網